Picture of ZYD9000L two-stage vacuum regeneration oil purifier insulating oil

　　ZYD9000L two-stage vacuum regeneration oil purifier is suitable for ZYD insulating oil two-stage oil purifier 1800L/H, ZJA high-efficiency insulating oil two-stage oil filter 3000L/H, two-stage insulating oil filter 6000L/H, two-stage vacuum filter Reference for the use of vacuum oil purifier purification equipment such as oil machine 9000L/H and two-stage transformer oil filter oil machine 12000/H. The pictures of the transformer oil filter vacuum oil filter are rich in content, and original real pictures were taken on site.

　　ZYD9000L two-stage vacuum regeneration oil purifier insulating oil picture:

　　The ZYD9000L two-stage vacuum regenerative oil purifier is widely used in power plants, power stations, power companies, and corporate power maintenance departments. It is suitable for large-scale transmission and transformation voltage equipment above 110KV and national main transformer grids, and is especially suitable for plateau areas above 800 meters above sea level. .

　　This machine is suitable for the vacuum filtration and deep purification of high-grade new oil, imported oil, transformer oil, ultra-high voltage transformer oil and other relatively expensive oils.

　　This machine can be used for vacuum oiling and drying of transformers, and it can be operated on-site with electricity.

　　This machine can effectively remove trace moisture, gas, and filter mechanical impurities in insulating oil, and improve the characteristics of insulating oil.

　　ZYD9000L two-stage vacuum regeneration oil purifier insulating oil characteristics:

　　1. Two-stage high vacuum and large pumping speed; it can quickly and efficiently remove water vapor in the oil, so that the dryness of the oil, the breakdown voltage value, and the one-time filtering effect are greatly improved, and the oil treatment period is shortened.

　　2. It has the functions of vacuum pumping and vacuum oiling of power equipment. It is used to treat other kinds of low-viscosity lubricating oil. Compared with a single-stage vacuum oil filter, it can increase the work efficiency by more than three times.

　　3. Advanced dehydration and degassing system, using large-area three-dimensional flash evaporation technology, can quickly remove harmful components such as moisture, gas and volatile components in the oil.

　　4. Precise filtration system, multi-stage filtration step-by-step encryption, can effectively remove mechanical impurities in the oil; high-quality filter material, corrosion resistance, good mechanical strength, durable.

　　5. The heating pipeline is specially designed to allow the oil to stay in the heating pipeline for a long time and to ensure that there is no dead point in the oil flow, so that the temperature of the oil from the inlet to the outlet can reach 30°C.

　　6. ​​Sensitive automatic pressure protection device and infrared liquid level control system, oil inlet and heating linkage system, constitute the whole machine chain safety protection system, simple operation, safe and reliable.

　　7. The multi-stage filter element is used, which is acid and alkali resistant, corrosion resistant, high temperature resistant, and can be backwashed, reducing the number of manual cleaning due to filter blockage, effectively improving work efficiency, and having a service life of up to 3 years.

　　8. This machine is equipped with automatic pressure controller, automatic alarm and shutdown for overpressure, automatic alarm and shutdown for oil shortage protection and other systems. It can be operated online to implement man-machine separation, interlocking protection devices, and safe and reliable operation.

　　ZYD9000L two-stage vacuum regeneration oil purifier insulating oil matters needing attention:

　　1. When the pressure gauge index on the oil purifier reaches 0.4Mpa and the machine stops, close the oil outlet valve of the vacuum tank and the oil inlet valve of the main oil tank; after cleaning the filter element of the fine filter (use coal or diesel oil, it is strictly forbidden to brush with hard steel wire) The surface of the filter element), put it into operation again; when the equipment is not used for a long time, drain the remaining oil.

　　2. Check the oil level of the vacuum pump at any time and keep the oil level of the vacuum pump up to the requirements; when purifying the oil with a lot of water, the vacuum pump oil should be replaced in time after emulsification. The vacuum pump should be replaced by No. 1 vacuum pump oil or 30~40 lubricating oil; (see the vacuum pump manual for details).

　　3. When it is necessary to purify another kind of oil, the remaining oil in the equipment should be drained manually or by an oil pump (for the method, see "Using the remaining oil drain device").

　　4. In case of emergency, press the "Total Emergency Stop" button and immediately close the oil inlet valve to cut off the power supply and the oil inlet circuit.

　　5. When the equipment starts to run, the oil flow in and out may be slow, and it will reach the normal state after the oil temperature rises.

　　6. In case of other failures, please refer to the failure analysis and troubleshooting methods on the back page of the manual or consult the after-sales service.

　　7. Observe whether there is moisture and sediment in the settling tank and cooler at any time and discharge it in time.

　　8. The manual bleed valve is open except when it is closed when refueling alone.

　　Equipment export packaging: The conventional fumigation packaging is suitable for long-distance transportation abroad.

　　Equipment transportation methods: shipping, air transportation, automobile transportation, etc. The company will replace and repair the goods for free until the customer is satisfied with the accident during the transportation and loading.

　　Sales consulting: Manager Zhang 0086-18580036904 (same number on WeChat) 0086-02386194345

　　(Need more video training files, add mobile phone WeChat or phone consultation to learn more)

　　Delivery cycle: standard models are available in stock.